Points for purchasing floor lamps, pay attention to the height of top-illuminated floor lamps; when purchasing top-illuminated floor lamps, consider the height of the ceiling and other factors. Take a floor lamp with a height of 1.70 meters to 1.80 meters as an example, and the ceiling height is above 2.40 meters. The best effect If the ceiling is too low, the light can only be concentrated in a local area, making people feel that the light is too bright and not soft enough. At the same time, when using top-illuminated floor lamps, the ceiling in the home should be white or light-colored, and the ceiling material should have a certain reflective effect. Pay attention to the luminosity of direct-illuminated floor lamps; pay attention to the purchase of direct-illuminated floor lamps. The lower edge of the lampshade is lower than the eyes, so that the eyes will not feel discomfort due to the light of the bulb. In addition, too much indoor light contrast will increase eye load, try to choose a floor lamp that can be dimmed. When in use, because the direct-illuminated light is concentrated, it is best to avoid mirrors and glass products near the reading position to avoid discomfort caused by reflections. Modeling floor lamps should pay attention to the style; if you buy a "modeling floor lamp", this kind of lamp can be said to be not used for lighting, it is more like a "light sculpture" in the environment in the home. Of course, when purchasing this type of floor lamp, you must consider its consistency with the overall style of your home. For example, a noble classic standing lamp made of heavy blood-flower stone is totally different from modern furniture with a streamlined style in Yuppie style. Floor lamp installation method

1. Preparation before installation

Before installation, read the installation drawings and the product manual of the floor lamp carefully, and prepare common tools for lamp installation, such as a flat-head Phillips screwdriver, a hammer, etc. After unpacking the parts, please don't confuse them. If there are many similar parts, the installation drawings will generally draw a comparison chart of the actual size, and the unused parts are crossed, which is very easy to distinguish the various parts.

2. Check before installation

Before installation, check the accessories of the floor lamp and other conditions. If you find that the floor lamp board is damaged, you can contact the merchant to repair it. Wherever screws, eccentric parts, and wooden shafts are to be installed, guide holes will be opened, so there is no need to worry about the positioning of the parts. It should be noted that the wrong parts should not be installed and then repeatedly screwed together, otherwise the plate will be easily damaged, and the installation will often cause instability and tilt.

3. Install floor lamps

Usually the floor lamp should have a cast iron chassis, which is slightly smaller than the surface base. The black plastic cap should be a fastener for fixing the lampshade. The order of parts from bottom to top should be: chassis fastening nut, cast iron chassis, base , Lamp poles, lamp holders, lamp shades, plastic fasteners, light bulbs. The power cord coming out of the floor lamp pole passes through the chassis fastening nut, cast iron chassis, and base, and then connects to the power cord and wraps it with electrical tape. The chassis should have a recess to extend the power cord. The floor lamp here reminds everyone that the power cord of the floor lamp must be handled properly. One is the safety of electricity, and the other is that it is not easy to trip people when walking around in the home.

Floor lamp maintenance skills:

1. Moisture-proof

The most important thing for electrical appliances is humidity, which will reduce the service life and be dangerous to electricity. Therefore, the key step in the maintenance of floor lamps is to prevent moisture, whether it is placed in the living room, or the lighting in the bathroom, bathroom, and the stove in the kitchen. The lamp must be equipped with a moisture-proof lampshade to prevent the intrusion of moisture and promote the rust damage or leakage short circuit of the lamp.

2. Dust removal

Floor lamp maintenance requires frequent dust treatment, especially the lampshade of floor lamp. The lampshade is easy to accumulate ash layer and cause darkening, which affects the lighting effect, so it should be cleaned frequently. When cleaning the lampshade of the floor lamp, use a clean feather duster to gently sweep away the dust, so as not to deform the lampshade. There are several situations for floor lamp dust removal and wiping:

(1) For normal cleaning, use a clean feather duster to gently dust off. Be very careful.

(2) If it is a non-metal floor lamp, it can be wiped clean with a damp cloth, taking care not to wipe the power cord.

(3) If it is a metal lamp, wipe it with a dry cloth, don't touch it with water.

Note: When cleaning and maintenance, disconnect the connected power supply first, and at the same time, be careful not to change the structure of the lighting, and do not change the parts of the lighting casually. After the cleaning and maintenance, the lighting should be installed as it is, and no missing or wrong installation Lighting parts, so as not to cause danger. At the same time, do not clean the lamp with water as much as possible, just wipe it with a dry cloth dampened with water. If you accidentally touch the water, try to wipe it dry as much as possible. Do not wipe it with a wet cloth immediately after turning on the light.

3. Don't switch frequently

When using lighting, try not to switch frequently, because when lighting is frequently started, the current through the filament is greater than the current during normal operation, which makes the temperature of the filament rise sharply and accelerate sublimation, which will greatly reduce its service life. One point that should be paid attention to in the maintenance of all lighting.